• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock replacement is a quick and cheap method to increase your home's security. However, the procedure isn't for everyone. It requires a certain amount of skill and patience.

The cylinder is contained within the knob's body. The cylinder is responsible to recognize the key when it is inserted in the lock.

The old lock can be removed

The first step to replace a door lock is to remove the old one. This is a relatively easy process, but there are some things to remember. Make sure that the new lock is compatible with your door. This will ensure that it fits securely and doesn't leave a gap in the deadbolt plug or latch.

Once you have removed the latch plate, look for two screws or bolts on the inside of the casing, which hold the casing and the halves of the double glazing window lock replacement together. Take these screws off using a screwdriver before removing the lock off the door. If you have a mortise upvc window locking mechanism repair system, there is a set screw that binds the handle to the spindle. Remove the doorknobs by unscrewing this screw using a screwdriver.

You must also remove the deadbolt latch and latch plug from the hole in your door jamb. Install your new lock. If you are replacing a mortise you must determine the distance between your lock's case and your door edge to ensure that your new lock fits.

Several reasons might prompt you to change the door lock, such as being concerned that someone else may have the key, or you are welcoming a new roommate. In any event, you could save money by taking the lock off yourself instead of paying an expert to do it. It is much easier than people think and can be done in just a few moments.

Remove the trim and handle of your door. With a flat screwdriver remove the trim. It should be possible to pull off the majority of it. In some instances, you may even be able remove the handles completely. Then, check the handle for a tiny hole on the interior side and insert a straightened paper clip into it. This will trigger the release mechanism and allow you to take the handle from the door. Then, look on the inside of the lock to find a small tab that you can press using a flat screwdriver. After the spindle is removed, you can remove the housing and cylinder.

Making a choice for a new lock

When it comes time to pick a new lock there are a lot of options. Consider the different types of locks and select one that fits the style of your door. Take into consideration the backset (the distance between the edge of the door and the center of the lock hole) and the cross bore (small hole that runs along the edge of the door frame). Choose a lock that fits the door's thickness and the swing.

The majority of door locks are graded by BHMA and the American National Standards Institute to provide you with an idea of how they are able to withstand the rigors of use and how difficult to disable or pick. A grade 3 lock may be ideal for a quiet suburban apartment complex, whereas a grade 1 lock might stand up to the traffic that is frequented by a retail storefront on a busy street.

Most smart door locks require digital code to open. If you are worried about hacking, or other security issues, talk to a professional locksmith.

replacing window locks the cylinder

It is easy to replace window locks upvc a damaged or broken door lock cylinder using an easy DIY project. It is important to select the correct cylinder and follow all instructions. First, remove the knob or handle, if it is present. Then using a screwdriver remove the trim that is around the lock cylinder. After the trim is removed, you will be able to access the screws that secure the cylinder and remove them with the flat-head screwdriver. The cylinder is then gently pulled out of the door.

Make sure you measure the length of the new cylinder prior to putting it in place. Find the distance from the center to the right and left sides of the cylinder with a tape measure. Then, you can purchase an additional cylinder using the same measurements. This will stop cylinders from snapping when the door is kicked or the key becomes stuck inside.

Once you have a suitable replacement cylinder, place it in the door and turn the key. This will align the cylinder with the carriage that is usually located on the outside of the lock. Then, loosen the set screw, which should be just a few turns inside the head. If there is a screw on the edge of the case that holds the door, you will have to loosen it.

You can replace the old lock cylinder with the new one by inserting it into the case and tightening the set screws. You should also reinstall the piece that connects the cylinder to the stem for the lock indicator and this can be done by pulling out three small tabs on back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the back of the cylinder. You must then install the latch plate and strike plate, along with the retaining rings that are connected to the top of the lock cylinder.

Installing a new lock

If you're replacing a previous lock, you should start by measuring the width of the door. Most residential locksets are designed for a door thickness of 1 3/8 - 3/4 inch. If your door is thicker, you will need a thick door kit that includes longer screws and an extended tail piece (for door knobs) or spindle extension (for deadbolts).

Most locks come with a detailed installation guide to help you. Be sure to read the instructions thoroughly prior to beginning the process to make sure that you are following all of the necessary steps. The booklet will also give you an idea of the level of expertise required to accomplish the task. It is possible to ask a person who has experience changing locks for assistance if you are changing a lock the first time.

It's a good idea to seal the openings of the old hardware before installing the new lock. This will stop screws from falling through the holes, and protect any tiles you have installed. It also shields your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a strip of painter's tape, which is designed to be used to protect your painter's tape, but you can also use gaffer's tape as well as masking tape if you have it available.

After removing the screws that hold the lock's inner half to the outside then remove the lock immediately. It's crucial to do this as quickly as possible to prevent the lock from accidentally closing on itself and damage the mechanism.

If your new lock is equipped with a latch bolt, fit the new latch bolt into its upper cross bore. Make sure that you place it in the right location, which is indicated by an arrow. Then, screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it few times to ensure that it extends all the way through the strike plate and is secured. Follow the instructions included in your electronic smart lock to program it. This requires downloading an app and creating an email address, confirming your identity, then accessing the wireless network to add your device.